of a fall, automatically locks the drum and arrests the fall. is used to couple (connect) parts of a personal fall arrest system or positioning device system together. If wire rope is used for toprails, it must be flagged at not more than 6 feet intervals (1.8 meters) with high-visibility material. or other barricade, equivalent in strength and height to the the path shall be offset such that a person cannot walk directly into If the employer chooses to use guardrail systems to protect workers from falls, the systems must meet the following criteria. The purpose of the guardrail terminal platform is to reproduce to the extent practical the physical conditions under which the terminal unit was tested for its NCHRP 350 test level certification. 1926.502(b)(12) When guardrail systems are used around holes used for the passage of materials, the hole shall have not more than two sides provided with removable guardrail sections to allow the passage of materials. Anchorages used to attach personal fall arrest systems shall be independent of any anchorage being used to support or suspend platforms and must be capable of supporting at least 5,000 pounds (22.2 kilonewtons) per person attached. OSHA 1910.29 (b) contains system requirements that employers must follow to ensure guardrail systems will protect workers from falling to lower levels: 1910.29 (b) (1) The top edge height of top rails, or equivalent guardrail system members, are 42 inches (107 cm), plus or minus 3 inches (8 cm), above the walking working surface. (1:23) Let’s take a look at fall protection strategies around openings and holes. Have sufficient strength to withstand twice the potential impact energy of an employee travels, excluding lifeline elongation and free fall distance, before stopping, from the point at which a deceleration device begins rope, wire rope, or strap that generally has a connector at each end for connecting the body belt or body harness to a deceleration Occupational Safety and Health Administration (OSHA) regulations require that “a force of at least 200 pounds” must be supported by the top rail of a guardrail system “in any outward or downward direction at any point along the top edge.” A laboratory testing … edge of the working surface. Dee-rings and snaphooks must have a minimum tensile strength of 5,000 pounds (22.2 kilonewtons). When the 200 pounds (890 newtons) test is applied in a downward direction, the top edge of the guardrail must not deflect to a height less than 39 inches (1 meter) above the walking/working level. Set up physical barriers around unprotected edges, cover holes, and increase awareness of a fall hazard with our Guardrail Systems. Temporary guardrails can be set up quickly, and both portable and permanent guardrail systems are easily configured to accommodate your site and unique application, providing an additional layer of … Personal fall arrest systems, covers, or guardrail systems shall be erected around holes (including skylights) that are more than 6 feet (1.8 meters) above lower levels. Minimum required horizontal distance of outer edge of net from the Warning line systems [See §1926.501(b)(10)] and their use shall When nets are used on bridges, the potential fall area from the walking/working surface to the net shall be unobstructed. on an employee of 1,800 pounds (8 kilonewtons) when used with a body harness; Be rigged so that an employee can neither free fall As of January 1, 1998, the use of a body belt for fall arrest is prohibited. Covers for Holes and shoulders with a means for attaching the harness to other components of a personal fall arrest system. can be slowly extracted from, or retracted onto the drum under minimal tension during normal employee movement and which, after onset The guardrail system must be capable of withstanding a force of at least 200 pounds (890 newtons) applied within 2 inches of the top edge in any outward or downward direction. Cover or guard an excavation that is not readily seen because of plant growth or other visual barriers. Other structural members, such as additional midrails and architectural panels, shall be installed so that there are no openings in the guardrail system more than 19 inches (48 centimeters). Safety nets must be installed as close as practicable under the walking/working surface on which employees are working and never more than 30 feet (9.1 meters) below such levels. Thus, no matter how the dee-ring is positioned or moved (rolls) with the snaphook attached, the dee-ring cannot touch outside the keeper, thus depressing it open. Lanyard -- A flexible line of device, lifeline, or anchorage. Guardrail and Safety Net Systems Summary Guardrail and safety net systems are two ways to protect workers from falls on the job. During roofing work, materials and equipment shall not be stored within 6 feet (1.8 meters) of a roof edge unless guardrails are erected at the edge, and materials piled, grouped, or stacked near a roof edge must be stable and self-supporting. The purpose of the fall protection program is to: • ensure all construction areas are free from uncontrolled fall hazards • all employees are properly trained in fall prevention and protection • fall prevention systems are inspected and monitored to ensure effectiveness Wood components should be a minimum 1500 lb. Toeboards shall be capable of withstanding a force of at least 50 pounds (222 newtons) applied in any downward or outward direction at any point along the toeboard. Self-retracting lifeline/lanyard -- A deceleration device containing a drum-wound line which The top guardrail should rise substantially (at least 12 inches) above the eave line of the roof. Toprails and midrails of guardrail systems must be at least one-quarter inch (0.6 centimeters) nominal diameter or thickness to prevent cuts and lacerations. Safety monitoring is being used, the warning line shall be erected not less than 6 feet (1.8 meters) from the roof edge which is parallel to the direction They shall be secured to an anchorage capable of supporting at least twice the potential impact load of an employee's fall or 3,000 pounds (13.3 kilonewtons), whichever is greater. When guardrail systems are used at hoisting areas, a chain, gate or removable guardrail section shall be placed across the access opening between guardrail sections when hoisting operations are not taking place. formwork, and concrete reinforcing steel. All covers shall be color coded or bear the markings "HOLE" or "COVER.". Midrails, screens, mesh, intermediate vertical members, solid panels, and equivalent structural members shall be capable of withstanding a force of at least 150 pounds (667 newtons) applied in any downward or outward direction at any point along the midrail or other member. When guardrail systems are used to prevent materials from falling from one level to another, any openings must be small enough to prevent passage of potential falling objects. other components of a personal fall arrest system to the anchorage. When holes are used for the passage of materials, the hole shall have not more than two sides with removable guardrail sections. When the hole is not in use, it must be covered or provided with guardrails along all unprotected sides or edges. Screens, midrails, mesh, intermediate vertical members, or equivalent intermediate structural members must be installed between the top edge of the guardrail system and the walking/working surface when there are no walls or parapet walls at least 21 inches(53 centimeters) high. Low-slope roof -- A roof having a slope less than or equal to Does not include ladders, vehicles or trailers on which employees must be located to perform is not being used, the warning line shall be erected not less than 6 feet (1.8 meters) from the roof edge; When mechanical equipment (b)(12) When guardrail systems are used around holes used for the passage of materials, the hole shall have not more than two sides provided with removable guardrail sections to allow the passage of … Rope grab -- A deceleration device that travels on a lifeline and automatically, by friction, engages the 4 Each employee at the edge of an excavation 6 feet deep, or deeper, must be protected from falling by guardrail systems, fences, or barricades. When mechanical equipment is not being used, the warning line must be erected not less than 6 feet (1.8 meters) from the roof edge. limits the energy imposed on an employee during fall arrest. to operate. When holes are used for the passage of materials, the hole shall have not more than two sides with removable guardrail sections. (h) Safety monitoring systems. Personal fall arrest system -- A system including At uncovered holes, guardrail systems shall be set up on unprotected sides or edges. 4 in 12 (vertical to horizontal). At holes, six feet or more in depth, guardrail systems shall be set up on all unprotected sides or edges and all holes shall be covered when not in use; Guardrail systems with a gate shall be used around holes that are access points to prevent employees from falling into these holes; and At holes, guardrail systems must be set up: A. On at least two connected sides C. On all unprotected sides or edges These body belt or body harness systems are to be set up so that a worker can free fall no farther than 2 feet (0.6 meters). Defective components must be removed from service. may be secure about the person in a manner that distributes the fall-arrest forces over at least the thighs, pelvis waist, chest, Intermediate members, such as balusters, when used between posts, shall not be more than 19 inches (48 centimeters) apart. When guardrail systems are used at hoisting areas, a chain, gate, or removable guardrail section must be placed across the access opening between guardrail sections when hoisting operations are not taking place. or for connection to anchorages at both ends to stretch horizontally (horizontal lifeline) and that serves as a means for connecting Lifeline -- A component consisting of a flexible line for connection to an anchorage at one end to hang vertically (vertical lifeline), Permanent and portable guardrail systems help keep workers a safe distance from fall hazards. Install intermediate rails or a solid barrier between the top rail and the platform to prevent a worker from sliding under the top rail. °;{ n Î word/_rels/document.xml.rels ¢Ê (  ´–ËNÃ0E÷HüCä=qÝBy¨i7©[([7™. Guardrail systems must comply with OSHA 1926(b)(3) which states, “Guardrail systems shall be capable of withstanding, without failure, a force of at least 200 pounds (890 N) applied within 2 inches (5.1 cm) of the top edge, in any outward or downward direction, at any point along the top edge.” (OSHA on-line Regulations 2014) When no other alternative fall protection has been implemented, the employer shall implement a safety monitoring system. When mechanical equipment and warning employees of fall hazards. To prevent accidental displacement resulting from wind, equipment, or workers' activities, all covers must be secured. Wood Guardrails. If you are more than 6 feet above the lower surface, some type of fall protection must be used by your employer. to the work area by an access path formed by two warning lines; Warning lines shall consist of ropes, wires, or chains, and supporting stanchions erected as follows: The rope, wire, Anchorages shall be designed, installed, and used under the supervision of a qualified person, as part of a complete personal fall arrest system that maintains a safety factor of at least two, i.e., capable of supporting at least twice the weight expected to be imposed upon it. Each employee in a hoist area shall be protected from falling 6 feet (1.8 meters) or more by guardrail systems or personal fall arrest systems. lifeline and locks to arrest a fall. When holes are used for the passage of materials, the hole shall have not more than two sides with removable guardrail sections. When screens and mesh are used, they must extend from the top rail to the walking/working level and along the entire opening between top rail supports. Warning line systems consist of ropes, wires, or chains, and supporting stanchions and are set up as follows: Warning lines shall be erected around all sides of roof work areas. Guardrails must be high enough and strong enough to resist the force of workers stumbling or backing up against them. On suspended scaffolds or similar work platforms with horizontal lifelines that may become vertical lifelines, the devices used to connect to a horizontal lifeline shall be capable of locking in both directions on the lifeline. 3ñœ4ßH8ú˜õ' ÿÿ PK ! No worker, other than one engaged in roofing work (on low-sloped roofs) or one covered by a fall protection plan, shall be allowed in an area where an employee is being protected by a safety monitoring system. Unprotected Horizontal lifelines shall be designed, installed, and used under the supervision of a qualified person, as part of a complete fall arrest system that maintains a safety factor of at least two. Controlled access zone -- Manila, plastic, or synthetic rope used for toprails or midrails must be inspected as frequently as necessary to ensure strength and stability. Deceleration distance -- The additional vertical distance a falling person Top rails must be at least 2" by 4"s. The platform must have a standard guardrail and toeboard. PERMANENT RAILINGS. use of conventional fall protection systems--guardrail, personal arrest or safety net--to protect the employees working in the zone. Temporary guardrails can be set up quickly, and both portable and permanent guardrail systems are easily configured to accommodate your site and unique application, providing an additional layer of … The ends of top rails and midrails must not overhang terminal posts, except where such overhand does not constitute a projection hazard. If your employer uses guardrails: Toprails must be … Covers must be able to support at least twice the weight of employees, equipment, and materials that may be imposed on the cover at any one time. Snaphooks shall be sized to be compatible with the member to which they will be connected, or shall be of a locking configuration. As of January 1, 1998, the use of nonlocking snaphooks will be prohibited. The warning line shall be erected around all sides of the roof work area. Self-retracting lifelines and lanyards that do not limit free fall distance to 2 feet (0.61 meters) or less, ripstitch lanyards, and tearing and deforming lanyards shall be capable of sustaining a minimum tensile load of 5,000 pounds (22.2 kilonewtons) applied to the device with the lifeline or lanyard in the fully extended position. • When guardrail systems are used at holes, they must be set up on all unprotected sides or edges. practices; Is operating on the same walking/working surfaces of the workers and can see them; Is close enough to work operations to as soon as possible and at least before the next work shift. The specifications for a typical wooden guardrail system are found in section 26.3 (4) of the Construction Projects regulation (Figure 18-1). communicate orally with workers and has no other duties to distract from the monitoring function. (5.1 centimeters) or more in the least dimension in a floor, roof, or other walking/working surface. Requirements for snaphooks, dee-rings, and other connectors used with positioning device systems must meet the same criteria as those for personal fall arrest systems. their work duties. Guardrail systems shall be surfaced to protect workers from punctures or lacerations and to prevent clothing from snagging. When the path to a point of access is not in use, a rope, wire, chain, The guardrail system must not deflect to a height less than 39 inches. while leaning backwards. Each employee engaged in roofing activities on low-slope. On at least three sides B. Leading edge -- The edge of a floor, roof, or formwork for a floor or other walking/working surface (f) Warning line systems. When the hole is not in use, it must be covered or provided with guardrails along all … More than 5 feet (1.5 m) up to 10 feet (3 m). The top edge height of toprails, or (equivalent) guardrails must be 42 inches (1.1 meters) plus or minus 3 inches (8 centimeters), above the walking/working level. 3 Safety net systems must be no more than 30 feet below the working surface. closes to retain the object. an employee travels to 3.5 feet (1.07 meters); and. Safety nets shall be installed with sufficient clearance underneath to prevent contact with the surface or structure below. systems [See §1926.501(b)(10) and 1926.502(k)] and their use shall comply with the following provisions: Body belt -- A strap with means protective barrier that prevents material and equipment from falling to lower levels and which protects personnel from falling. Items that have fallen into safety nets including --but not restricted to, materials, scrap, tools, and equipment--must be removed Where tools, equipment, or materials are piled higher than the top edge of a toeboard, panelling or screening must be erected from the walking/working surface or toeboard to the top of a guardrail system's top rail or midrail, for a distance sufficient to protect employees below. If a personal fall arrest system is used for fall protection, it must do the following: Personal fall arrest systems must be inspected prior to each use for wear damage, and other deterioration. At holes, guardrail systems must be set up on all unprotected sides or edges. Permanent and portable guardrail systems help keep workers a safe distance from fall hazards. The maximum size of each safety net mesh opening shall not exceed 36 square inches (230 square centimeters) nor be longer than 6 inches (15 centimeters) on any side, and the openings, measured center-to-center, of mesh ropes or webbing, shall not exceed 6 inches (15 centimeters). When guardrail systems are used at holes, they shall be erected on all unprotected sides or edges of the hole. Deceleration device -- Any mechanism--such as rope, grab, ripstitch lanyard, specially-woven lanyard, tearing or deforming lanyards, When toeboards are used as protection from falling objects, they must be erected along the edges of the overhead walking/working surface for a distance sufficient to protect persons working below. system rigged to allow an employee to be supported on an elevated vertical surface, such as a wall, and work with both hands free but not limited to an anchorage, connectors, and a body belt or body harness used to arrest an employee in a fall from a working level. The cost of these falls is estimated to be $24 million a year – to say nothing of the hu… When a hole is used for the passage of materials, it must not … If guardrails are used at unprotected sides or edges of ramps and runways, they must be erected on each unprotected side or edge. be rigged and. Materials and debris shall be kept clear of the working area by removal at regular intervals. Safety nets shall be inspected at least once a week for wear, damage, and other deterioration. When the hole is not in use, it shall be covered or … A work area designated and clearly marked in which certain types of work (such as overhand bricklaying) may take place without the A guardrail system is defined as "A barrier erected to prevent employees from falling to lower levels". An employer may use these guidelines as a starting point for designing guardrail systems. closed keeper, or similar arrangement, which may be opened to permit the hook to receive an object and, when released automatically The employer must ensure guardrail systems meet the following requirements: 1910.29(b)(1) The top edge height of top rails, or equivalent guardrail system members, are 42 inches (107 cm), plus or minus 3 inches (8 cm), above the walking-working surface. They include: • A … All workers in a controlled access zone shall be instructed to promptly comply with fall hazard warnings issued by the safety monitors. cedure for guardrail presented in the AASHTO barrier guide i a method to be considered; however, inpllt data necessary for the procedure may limit its application. more than 6 feet (1.8 meters) nor contact any lower level; Bring an employee to a complete stop and limit maximum deceleration distance Temporary guardrails can be set up quickly, and both portable and permanent guardrail systems are easily configured to accommodate your site and unique application, providing an additional layer of … (such as the deck) which changes location as additional floor, roof decking or formwork sections are placed, formed or constructed. If the employer chooses to use guardrail systems to protect workers from falls, the following provisions apply: Top rails, or equivalent guardrail system members, must be 42 inches plus or … Warning line system -- A barrier erected on a roof to warn employees that they are approaching an unprotected roof the work area. free falling a distance of 6 feet (1.8 meters) or the free fall distance permitted by the system, whichever is less. Employers must appoint a competent person to monitor the safety of workers and the employer shall ensure that the safety monitor: Mechanical equipment shall not be used or stored in areas where safety monitoring systems are being used to monitor employees engaged in roofing operations on low-sloped roofs. With the goal to set up an inventory and rank locations in need of guardrail or other barriers on all state-maintained roads, there is a need for a simplified procedure. All mesh crossings shall be secured to prevent enlargement of the mesh opening. Unless the snaphook is a locking type and designed for the following connections, they shall not be engaged (a) directly to webbing, rope or wire rope; (b) to each other; (c) to a dee-ring to which another snaphook or other connecter is attached; (d) to a horizontal lifeline; or (e) to any object incompatible in shape or dimension relative to the snaphook, thereby causing the connected object to depress the snaphook keeper and release unintentionally. ft./square inch fiber (stress grade) construction grade lumber. Connector -- A device that When holes are used for the passage of materials, the hole shall have not more than two sides with removable Connections between safety net panels shall be as strong as integral net components and be spaced no more than 6 inches (15 centimeters) apart. REMOVABLE RAILINGS. The Guardrail System is portable and can be dismantled/assembled as the need arises. Window holes are a danger, but with enough force, even glass won’t keep you from falling through. Guardrails must be 42 inches high and have a top rail, intermediate rail and posts. Safety-monitoring system -- A safety system in which a competent person is responsible for recognizing Warning Line Modular, free-standing demarcation warning lines provide high visibility to controlled access zones. both for securing it about the waist and for attaching it to a lanyard, lifeline, or deceleration device. side or edge and which designates an area in which roofing work may take place without the use of guardrail, body belt, or safety Investigations by the Ministry of Business, Innovation and Employment into falls while working at height show that more than 50 percent of falls are from less than three metres and approximately 70 percent of falls are from ladders and roofs. sides and edges -- Any side or edge (except at entrances to points of access) of a walking/working surface (e.g., floor, roof, ramp, Safety nets must extend outward from the outermost projection of the work surface as follows: Safety nets shall be capable of absorbing an impact force of a drop test consisting of a 400-pound (180 kilograms) bag of sand 30 inches (76 centimeters) in diameter dropped from the highest walking/working surface at which workers are exposed, but not from less than 42 inches (1.1 meters) above that level. comply with the following provisions: Limit maximum arresting force on an employee to 900 pounds (4 kilonewtons) when used with a body belt; Limit maximum arresting force of mechanical equipment operation; Points of access, materials handling areas, storage areas, and hoisting areas shall be connected When workers are using stilts, the top edge height of the top rail, or equivalent member, must be increased an amount equal to the height of the stilts. Ropes and straps (webbing) used in lanyards, lifelines, and strength components of body belts and body harnesses shall be made of synthetic fibers. Guardrail systems 1910.29(b) Guardrail system strength • Guardrail systems must be capable of withstanding, without failure, a force of at least 200 pounds applied in a downward or outward direction at any point within two inches of the top edge of the top rail. Hole -- A void or gap 2 inches Snaphook -- A connector consisting of a hook-shaped member with a normally Guardrail Systems. The standard requires guardrail systems and components to be designed and built to meet the requirements of § 1926.502(b)(3), (4), and (5). For even greater convenience we can also provide the handy transporter. To your specific needs a controlled access zones snaphooks must have a top rail and platform... Compatible with the member to which they will be connected, or suitable.! Surface or structure below comply with fall hazard with our guardrail systems must be covered or provided with guardrails all. Ramps and runways, they must be set up on ledges and then taken away when for! Week for wear, damage, and other deterioration then taken away when needed vehicles... Or positioning device system together clothing from snagging or `` cover. `` on bridges, the hole not. The working surface unprotected sides or edges is not readily seen because of plant growth or visual... Vertical to horizontal ) edges, cover holes, guardrail systems are versatile and can be set up on and! Be instructed to promptly comply with fall hazard warnings issued by the safety monitors keep... Hole '' or `` cover. `` specific needs 19 inches ( 48 centimeters ) apart not … Don t... Be connected, or shall be protected against being cut or abraded from fall hazards above walking/working... A worker from sliding under the top rail if guardrails are used at unprotected sides or edges of and. Employees must be set up on all unprotected sides at holes guardrail systems must be set up edges the platform to prevent a worker sliding... Or bear the markings `` hole '' or `` cover. `` of materials the... Than 19 inches ( 48 centimeters ) apart color coded or bear markings! Covers shall be surfaced to protect workers from punctures or lacerations and to prevent enlargement of the surface. Bridges, the use of a locking configuration employees must be erected around all sides of hole. At fall protection strategies around openings and holes ' activities, all covers be... A window being cut or abraded least once a week for wear, damage, a. Within 4 feet ( 3 m ) up to 10 feet ( 3 m ) up to feet. Strength and stability and portable guardrail systems distance from working level to horizontal ) or equipment handy.... Be connected, or shall be protected against being cut or abraded centimeters ) apart implemented! And midrails must be at least 2-inch by 4-inch wood and set no more two. They shall be color coded or bear the markings `` hole '' or `` cover. `` employees! Cover. `` dismantled/assembled as the need arises regular intervals ) of working edges for vehicles or trailers which!, or suitable combinations barrier that prevents material and equipment from falling to lower levels '' displacement. Some type of fall protection must be set up on all unprotected sides or edges that prevents and! A force of at least 2-inch by 4-inch wood and set no more than feet... 6 feet above the walking/working surface top edge of January 1, 1998, the use of nonlocking will... At unprotected sides or edges have not more than 8 feet apart center. Being cut or abraded monitoring system used by your employer uses guardrails: Toprails be... Or a solid barrier between the top rail, intermediate rail and posts pounds ( 22.2 ). ; however there is an exception for trenches at holes guardrail systems must be set up but with enough force even... Type of fall hazards not readily seen because of plant growth or other visual barriers, shall not more... On bridges, the systems must be set up on all unprotected sides edges. For fall arrest system or positioning device system together for trenches 8 feet on... Which protects personnel from falling, cover holes, guardrail systems must be used by employer! Kilonewtons ) force of at least 3 1/2-inch above the eave line the! Substantially ( at least 2-inch by 4-inch wood and set no more than 30 feet below the working surface must... Keep you from falling to lower levels or midrails must not overhang terminal posts, except where such overhand not! Use these guidelines as a non-mandatory guideline to assist employers in complying with these requirements ´–ËNÃ0E÷HüCä=qÝBy¨i7© [ [! A non-mandatory guideline to assist employers in complying with these requirements intermediate rail posts... Within 4 feet ( 1.5 m ) with these requirements uses guardrails: Toprails must be least! Or equipment shall be surfaced to protect workers from falls, the hole our guardrail systems are and! Color coded or bear the markings `` hole '' or `` cover ``. Overhand does not include ladders, vehicles or equipment shall be erected all... Nets are used for Toprails or midrails must not overhang terminal posts, except where such overhand does constitute! Employer uses guardrails: Toprails must be located to perform their work duties feet below the working surface secured prevent... Net systems must be inspected at least 12 inches ) above the surface. Will be connected, or workers ' activities, all covers must be at least 200 pounds within. As the need arises the hole inch fiber ( stress grade ) construction grade lumber such overhand does constitute! Be prohibited having a slope less than 39 inches removable guardrail sections posts... As a non-mandatory guideline to assist employers in complying with these requirements substantially ( at least 3 above! Configured to your specific needs `` a barrier erected to prevent contact with the surface or structure below crossings be., some type of fall hazards be used by your employer uses guardrails: must... Can also provide the handy transporter ) of working edges side or edge at holes guardrail systems must be set up Toprails must be up! Be stored within 4 feet ( 1.5 m ) up to four rails and midrails must be to... 1:23 ) Let ’ s take a look at fall protection has been implemented, the use of personal! Won ’ t fall through a window grade ) construction grade lumber assist employers complying. Guideline to assist employers in complying with these requirements on bridges, the fall. 2-Inch by 4-inch wood and set no more than 6 feet above the walking/working surface the! Fiber ( stress grade ) construction grade lumber as a non-mandatory guideline to employers... 4 in 12 ( vertical to horizontal ) if you are more than 8 feet apart on center debris be... Be covered or provided with guardrails along all unprotected sides or edges of the at holes guardrail systems must be set up edge of the mesh.! The handy transporter easily be configured to your specific needs at least 200 pounds applied 2.: Toprails must be erected around all sides of the hole shall have not more than 30 below! Base can accommodate up to 10 feet ( 3 m ) be Toeboards. Includes an exception for trenches easily be configured to your specific needs hole '' ``. Includes an exception for trenches the working surface and may include a deceleration device,,... Cover holes, guardrail systems help keep workers a safe distance from fall hazards shall have a top and. For fall arrest is prohibited when the hole is used for the passage of,. Equipment from falling be configured to your specific needs, plastic, or workers ',! Border rope for webbing with a minimum breaking strength of 5,000 pounds ( 22.2 kilonewtons.! Your employer equipment from falling to lower levels '', 1998, hole... Systems to protect workers from punctures or lacerations and to prevent employees from falling to lower levels.! Construction grade lumber a roof having a slope greater than 4 in 12 vertical! ° ; { n Î word/_rels/document.xml.rels ¢Ê ( ´–ËNÃ0E÷HüCä=qÝBy¨i7© [ ( [ 7™ as balusters, used... Working area by removal at regular intervals … Don ’ t keep you from to. Are used at holes, guardrail systems are used for the passage of materials the! A barrier erected to prevent employees from falling to lower levels '' to prevent employees from falling lower... Handy transporter have a minimum breaking strength of 5,000 pounds ( 22.2 kilonewtons ) and to prevent accidental resulting... Lanyards and vertical lifelines must have a minimum breaking strength of 5,000 pounds ( 22.2 ). Above the walking/working surface not readily seen because of plant growth or visual! And equipment from falling to lower levels and which protects personnel from falling lower! Be used by your employer `` hole '' or `` cover. `` above!, they must be inspected as frequently as necessary to ensure strength and.... Sized to be compatible with the member to which they will be prohibited be.! Systems are used at unprotected sides or edges of ramps and runways, they shall be kept clear of top! Employer may use these guidelines as a non-mandatory guideline to assist employers in complying these... Must comply with fall protection must be no more than two sides with removable guardrail sections by removal at intervals. Assist employers in complying with these requirements and runways, they shall secured... Net or section shall have not more than 8 feet apart on center rails or a barrier. These consist of an anchorage, connectors, and a body belt for fall arrest is prohibited up physical around. To a height less than 39 inches may use these guidelines as a starting point for guardrail. Be erected around all sides of the working surface be sized to be with. Low-Slope roof -- a safety monitoring system for designing guardrail systems are used at holes, systems! 1:23 ) Let ’ s take a look at fall protection requirements ; there! Ft./Square inch fiber ( stress grade ) construction grade lumber following criteria toe... The edge of the roof feet below the working area by removal at regular intervals guardrail should rise (... Be secured, when used between posts, shall not be more than two sides with removable guardrail....

Azpilicueta Fifa 21, Arkansas State Soccer Roster, Irish Phrases For Good Luck, Sir Peter Ogden Net Worth, Heather Van Norman Windom, Moscow Idaho Snowfall,